IS_GTE
Posts : 5 Join date : 2011-03-25
| Subject: ProEFI 128 fault codes Tue Aug 07, 2012 7:35 pm | |
| Hello,
My proefi has been tossing some fault codes...
Uego1_RangeLow DriveShaftRPmLimit_Exc Map_Sticking
The car runs and starts perfectly. All snsors read properly. It doesn't show fault codes til a few minutes after start up. When Map_Sticking fault code comes on, the map sensor still reads properly. When the Uego1_RangeLow fault code comes on, the sensor goes fully lean 22.00. The has a noticeable exhaust note change. I have second wideband external gauge and it shows the afr holding steady around 14-15 afr at idle. If I blip the throttle the sensor starts reading again properly again. Then a minute later it throw the fault again. It happens randomly cruising as well, but not very often. Never happens at wot. The external wideband continues to to read proper afr with out fail.
When the DriveShaftRPmLimit_Exc fault code comes on I don't notice anything change.
I check all the wiring. I even when as far as pulling all the wires to those sensors and re wiring them back up.
Is there something I'm over looking? What do these codes mean?
Thanks
| |
|
AlbertTRDsupra
Posts : 2 Join date : 2012-09-10
| Subject: Re: ProEFI 128 fault codes Mon Sep 10, 2012 8:26 am | |
| - IS_GTE wrote:
- Hello,
My proefi has been tossing some fault codes...
Uego1_RangeLow DriveShaftRPmLimit_Exc Map_Sticking
The car runs and starts perfectly. All snsors read properly. It doesn't show fault codes til a few minutes after start up. When Map_Sticking fault code comes on, the map sensor still reads properly. When the Uego1_RangeLow fault code comes on, the sensor goes fully lean 22.00. The has a noticeable exhaust note change. I have second wideband external gauge and it shows the afr holding steady around 14-15 afr at idle. If I blip the throttle the sensor starts reading again properly again. Then a minute later it throw the fault again. It happens randomly cruising as well, but not very often. Never happens at wot. The external wideband continues to to read proper afr with out fail.
When the DriveShaftRPmLimit_Exc fault code comes on I don't notice anything change.
I check all the wiring. I even when as far as pulling all the wires to those sensors and re wiring them back up.
Is there something I'm over looking? What do these codes mean?
Thanks
I Also have this "Map_sticking" fault. car revs fine, but if I try to drive it it breaks up really bad. Can anyone tell him and me what this Map_sticking fault is? how to diagnose it? How to repair it? | |
|
Admin Admin
Posts : 258 Join date : 2008-02-22
| Subject: Re: ProEFI 128 fault codes Tue Jan 01, 2013 10:10 pm | |
| - AlbertTRDsupra wrote:
- IS_GTE wrote:
- Hello,
My proefi has been tossing some fault codes...
Uego1_RangeLow DriveShaftRPmLimit_Exc Map_Sticking
The car runs and starts perfectly. All snsors read properly. It doesn't show fault codes til a few minutes after start up. When Map_Sticking fault code comes on, the map sensor still reads properly. When the Uego1_RangeLow fault code comes on, the sensor goes fully lean 22.00. The has a noticeable exhaust note change. I have second wideband external gauge and it shows the afr holding steady around 14-15 afr at idle. If I blip the throttle the sensor starts reading again properly again. Then a minute later it throw the fault again. It happens randomly cruising as well, but not very often. Never happens at wot. The external wideband continues to to read proper afr with out fail.
When the DriveShaftRPmLimit_Exc fault code comes on I don't notice anything change.
I check all the wiring. I even when as far as pulling all the wires to those sensors and re wiring them back up.
Is there something I'm over looking? What do these codes mean?
Thanks
I Also have this "Map_sticking" fault. car revs fine, but if I try to drive it it breaks up really bad. Can anyone tell him and me what this Map_sticking fault is? how to diagnose it? How to repair it? A map sticking fault means just that...when the ignition is turned on, the map sensor is not passing the minimum threshold to determine that it is moving with throttle properly. This should be diagnosed and adjusted by your tuner. | |
|
Sponsored content
| Subject: Re: ProEFI 128 fault codes | |
| |
|