ProEFI

Electronic Fuel Injection Discussion Forums
 
HomeFAQSearchRegisterUsergroupsLog in

Share | 
 

 changing units and virtual gauges?

View previous topic View next topic Go down 
AuthorMessage
rich



Posts : 24
Join date : 2011-05-24
Location : Raleigh, NC

PostSubject: changing units and virtual gauges?   Tue May 24, 2011 7:55 am

I downloaded the latest version of Proefi 2.66 so I could take a look to what I am getting into with a 128 box for my G35. I'm used to the feel of Haltech software.

Few questions

is there an option to change pressure from kpa to psi, and all the other units as well?

Can you change the virtual gauges on the main page as well as their units, size etc?

What does ADC mean and is it a linear scale? Ie, for aftermarket sensors you have to input high and low fault values. How do you associate 0.5V with xx ADC and 4.5V with xxx ADC?

There isnt an xcal file in the software for a VQ35. There's supra and GTR, but no VQ. Is a tailored base map provided at the time of purchase?

Thanks!


Back to top Go down
View user profile
rich



Posts : 24
Join date : 2011-05-24
Location : Raleigh, NC

PostSubject: Re: changing units and virtual gauges?   Wed Jun 01, 2011 11:33 pm

bump?
Back to top Go down
View user profile
Psychoballistic



Posts : 1
Join date : 2011-05-11

PostSubject: Re: changing units and virtual gauges?   Thu Jun 16, 2011 12:08 pm

rich wrote:
I downloaded the latest version of Proefi 2.66 so I could take a look to what I am getting into with a 128 box for my G35. I'm used to the feel of Haltech software.

Few questions

is there an option to change pressure from kpa to psi, and all the other units as well?

Can you change the virtual gauges on the main page as well as their units, size etc?

What does ADC mean and is it a linear scale? Ie, for aftermarket sensors you have to input high and low fault values. How do you associate 0.5V with xx ADC and 4.5V with xxx ADC?

There isnt an xcal file in the software for a VQ35. There's supra and GTR, but no VQ. Is a tailored base map provided at the time of purchase?

Thanks!

+1 would definitely like to change my units of measurement as well.

Back to top Go down
View user profile
Admin
Admin


Posts : 258
Join date : 2008-02-22

PostSubject: Re: changing units and virtual gauges?   Sat Aug 06, 2011 3:09 pm

rich wrote:
I downloaded the latest version of Proefi 2.66 so I could take a look to what I am getting into with a 128 box for my G35. I'm used to the feel of Haltech software.

Few questions

is there an option to change pressure from kpa to psi, and all the other units as well?

Can you change the virtual gauges on the main page as well as their units, size etc?

What does ADC mean and is it a linear scale? Ie, for aftermarket sensors you have to input high and low fault values. How do you associate 0.5V with xx ADC and 4.5V with xxx ADC?

There isnt an xcal file in the software for a VQ35. There's supra and GTR, but no VQ. Is a tailored base map provided at the time of purchase?

Thanks!



Currently you can't change the displayed units, or the layout of the pages. You can log in whatever units you like however, just select the appropriate channel from the log list.

ADC is Analog to Digital Conversion. 0 is 0 volts, 1023 is 5volts, and yes, it is linnear.

A base map can be loaded when you purchase your unit, consult your ProEFI dealer on your needs.
Back to top Go down
View user profile http://proefiforum.forumakers.com
Sponsored content




PostSubject: Re: changing units and virtual gauges?   

Back to top Go down
 
changing units and virtual gauges?
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» 1977 Monte Carlo Install after market gauges in existing dash
» does changing the rear drive change the odometer signal?
» Changing rod bearings
» Write-Up: Fuel / Oil Pressure Sending & Gauges
» Changing golf grips - DIY

Permissions in this forum:You cannot reply to topics in this forum
ProEFI :: ProEFI Forums :: Products :: User Software-
Jump to: